NEC SL1100 Features And Specifications Manual Download | Manualshive

Page: 133 / 864

background image

• Trunks with Privacy Release enabled display Caller ID until the call is answered. To view it after the

call has been picked up, press the line key, which sets the call to private mode. To keep the call on
Privacy Release, press

Help

+

Exit

keys.

• An extension user can display the Caller ID information for a call in Park if Automatic Handsfree in

PRG 15-02-08 is set to 0 (Preselect).

• An extension user can display the Caller ID information for multiple incoming calls without answering

the call by pressing the line key if Automatic Handsfree in PRG 15-02-08 is set to 0 (Pre-select).

• Caller ID information outputs on the SMDR report.
• The system can send Caller ID digits to the voice mail if allowed in PRG 14-01-22.
• When there are more than 20 characters set in PRG 20-20 : Message Setup for Non-Caller ID Data,

either the first or last character is missing (based on the entry in PRG 20-19-01).

• If PRG 20-09-06: Class of Service Options (Incoming Call Service): Incoming Time Display is set to

1 (On), the first line displays the time and date.

• PRG 15-07-01 button (63) when enabled, removes the CPN from the setup message when making

an outbound ISDN call, this is a toggle enable/disable button and can be used on a Call-by-Call
basis. PRG 14-01-20, PRG 14-01-21 and PRG 20-08-15 are used for analog trunks only and can
only be set on a per trunk/Class of Service basis.

• SLT cannot block an incoming call based on the incoming Caller ID information on a station-by-

station basis.

• The CPU with MEMDB has 32 resources for DTMF receiving and Dial Tone detection. When a

EXIFE installed there are 32 resources available.

• When PRG 10-09-01 is set to 0 (Common) and PRG 14-02-10 (Caller ID) is set to 1 (Yes), all

DTMF/Dial Tone Detection resources are always allocated to analog trunks, not analog extensions.
However, if PRG 14-02-10 (Caller ID) is set to 0 (No), all DTMF/Dial Tone Detection resources can
be used for both analog trunks and analog extensions.

• For the Caller ID List to show calls to a station that received a busy tone, PRG 15-02-57 must be set

1 (On).

• When PRG 15-02-57 is set to 1 (On) and PRG 15-02-34 is set to 0 (Trunk), only outside calls are

shown in the Caller ID List.

• Caller ID history is not updated for a phone which is in power cutting mode from the ecology feature.

Once power is restored to the phone the caller ID history will start functioning again.

Default Settings

Disabled

System Availability

Terminals

All Multiline Terminals with a display and Single Line Terminals equipped to receive Caller ID

Required Component(s)

COIDB-B1

2BRIDB-C1

1PRIU-C1

ISSUE 2.0

SL1100

Features and Specifications Manual

1-121

C

«
...
131
132
133
134
135
...
»

Summary of Contents for SL1100

































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SL1100

Brand: ABB Pages: 138

Brand: ABB Pages: 116

Brand: auna multimedia Pages: 124

Brand: Nakamichi Pages: 11

Brand: Grandstream Networks Pages: 12

Brand: Invacare Pages: 45

Brand: AETA Pages: 136

Brand: Micronix Pages: 16

Brand: Nakamichi Pages: 11

Brand: Teufel Pages: 16

Brand: Blaupunkt Pages: 103

Brand: Aritech Pages: 28

Brand: Kenwood Pages: 72

Brand: Kenwood Pages: 84

Brand: Kenwood Pages: 44

Brand: Kenwood Pages: 48

Brand: Kenwood Pages: 48

Brand: Aastra Pages: 134

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands