manualshive.com logo in svg

Motorola DragonBall MC9328MX1, Reference Manual

The Motorola DragonBall MC9328MX1 Reference Manual is a comprehensive guide that provides detailed instructions for operating this powerful device. You can easily download this manual free of charge from our website, where we offer a range of user manuals for various products. Explore the full potential of your MC9328MX1 with this essential resource.

Share
Download
background image

28-44

MC9328MX1 Reference Manual

MOTOROLA

USB Device Port

28.7.6.2   The SYNCH_FRAME Standard Request

The SYNCH_FRAME standard request allows synchronization between the USB host and device during 
isochronous operations. The command is passed through endpoint 0 as a device request and must be 
processed by the device driver software.

28.8   Interrupt Services

The USB module generates a number of interrupts to indicate situations requiring attention from the host. 
The types of interrupts are broken into two categories: USB general interrupts and Endpoint specific 
interrupts. These interrupts are discussed in this section, as well as missed interrupts and their behaviors.

28.8.1   USB General Interrupts

The USB general interrupts indicate such things as global configuration and status changes pertaining to 
the USB. All of these interrupts are maskable. When an event causes an interrupt condition to occur, and 
the corresponding bit in the interrupt mask register is zero, an interrupt signal asserts on the module’s 
interface. Writing 1 to the associated bit in the interrupt register clears the interrupt. After a hard reset, all 
interrupts are masked by default. This section describes each of the USB General Interrupts.

28.8.1.1   MSOF—Missed Start-of-Frame

The MSOF interrupt is used to inform software that it did not service the SOF interrupt before another SOF 
interrupt was received.

28.8.1.2   SOF—Start-of-Frame

The SOF interrupt means that a start-of-frame token was received by the device. The current USB frame 
number can be read from the USB_FRAME register. The start-of-frame interrupt is usually used by 
isochronous devices to provide a stable timebase.

28.8.1.3   RESET_STOP—End of USB Reset Signaling

The RESET_STOP interrupt means that reset signaling on the USB has stopped.

28.8.1.4   RESET_START—Start of USB Reset Signaling

The RESET_START interrupt indicates that reset signaling on the USB has begun. When reset signaling is 
active on the USB, the device does not expect to receive any transactions on the bus. This interrupt results 
in a reset of the UDC into the powered state, however it does not cause any specific actions in the USB 
Core front-end logic. User software must clear any pending interrupts and ensure that the module is 
configured properly after the reset. This interrupt indicates the start of reset signaling. Status of the USB at 
any given moment can be verified by examining the USB_STAT register.

Presence of USB reset signaling invalidates any transaction in progress. On detection of RESET_START, 
user software reads any remaining valid data from the receive FIFOs and flushes all others. When reset 
signaling is detected, user software must clear any pending interrupts and ensure that the module is 
configured properly after the reset.

Summary of Contents for DragonBall MC9328MX1









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DragonBall MC9328MX1

Hama 39707 Operating Instruction preview
39707
Brand: Hama Pages: 4
Automationdirect.com CLICK PLUS C2-02CPU Quick Start Manual preview
CLICK PLUS C2-02CPU
Brand: Automationdirect.com Pages: 10
Lucent Technologies PARTNER Voice Messaging PC Card Release 2 Installation And Programming preview
PARTNER Voice Messaging PC Card Release 2
Brand: Lucent Technologies Pages: 67
MSNswitch UIS-322b Quick Installation Manual preview
UIS-322b
Brand: MSNswitch Pages: 2
Xcellon DRD-501 User Manual preview
DRD-501
Brand: Xcellon Pages: 24
Renesas Emulation Memory Board R0E330850MSRC0 User Manual preview
Emulation Memory Board R0E330850MSRC0
Brand: Renesas Pages: 4
Avigilon NVR5-STD-10GBE Installation Manual preview
NVR5-STD-10GBE
Brand: Avigilon Pages: 12
IMC Networks Wireless Outdoor Bridge XI-1500-IH Quick Installation Manual preview
Wireless Outdoor Bridge XI-1500-IH
Brand: IMC Networks Pages: 13
TEC Control WiDiCast User Manual preview
WiDiCast
Brand: TEC Control Pages: 4
Multitech MultiModem ISIHP-2S User Manual preview
MultiModem ISIHP-2S
Brand: Multitech Pages: 155
Multitech FaxFinder FF-120 Administrator User Manual preview
FaxFinder FF-120
Brand: Multitech Pages: 20
ADTRAN NetVanta 1224 Quick Start Manual preview
NetVanta 1224
Brand: ADTRAN Pages: 2
ADTRAN 1200934L1 Installation Instructions preview
1200934L1
Brand: ADTRAN Pages: 2
ADTRAN 17005660F1 Quick Start preview
17005660F1
Brand: ADTRAN Pages: 4
ADTRAN 1442823F1 Quick Start Manual preview
1442823F1
Brand: ADTRAN Pages: 4
ADTRAN NetVanta Series Quick Configuration Manual preview
NetVanta Series
Brand: ADTRAN Pages: 7
ADTRAN NetVanta 2000 Series Quick Start Manual preview
NetVanta 2000 Series
Brand: ADTRAN Pages: 15
ADTRAN 834-5 Installation Manual preview
834-5
Brand: ADTRAN Pages: 14

Brands by name

Popular brands

Load more brands