manualshive.com logo in svg

Motorola DragonBall MC9328MX1, Reference Manual

The Motorola DragonBall MC9328MX1 Reference Manual is a comprehensive guide that provides detailed instructions for operating this powerful device. You can easily download this manual free of charge from our website, where we offer a range of user manuals for various products. Explore the full potential of your MC9328MX1 with this essential resource.

Share
Download
background image

General Operation

MOTOROLA

SDRAM Memory Controller

24-29

the physical size constraints of the target applications, the design was optimized for a memory device data 
width of 32 bits. Table 24-12 summarizes the devices targeted by the design. The controller is capable of 
interfacing with devices of other widths and densities, however, only devices with 4 banks are supported. 
A 100 MHz system bus operation is possible with PC100 compliant single data rate memory devices.

24.7.1   Address Multiplexing

The JEDEC standard SDRAMs for which the controller was optimized, use an asymmetrical array 
architecture with more row than column address lines. The SDRAM Controller multiplexes only those pins 
which change between the row and column addresses. The remaining (most significant) row addresses and 
the bank addresses are not multiplexed. 

24.7.1.1   Multiplexed Address Bus

The SDRAM Controller multiplexed address bus is aligned to the column addresses so that address line A1 
always appears on pin MA0. With this alignment, the “folding point” in the multiplexor is driven solely by 
the number of column address bits, although interleave mode causes a two bit shift to account for the bank 
addresses. Column bus widths of 8 to 11 bits are supported in non-interleave mode, although only 8 and 9 
bit widths are allowed in interleave mode. Table 24-13 summarizes the multiplex options supported by the 
controller. Column addresses through A10 are driven regardless of the multiplexor configuration, although 
some of the lines will be unused for the smaller page sizes.

Memory width does not affect the multiplexer; however, it does affect how the memories are connected to 
the SDRAM Controller pins. The width of the multiplexed bus is one bit larger than in previous 
generations of the SDRAMC so that 32-bit memory systems can be supported with a minimal impact on 
the multiplex hardware because 32-bit memory systems are shifted left by one bit and use MA [n+1:1]. 
This is demonstrated in the last two rows of Table 24-13 by the grayed-out boxes. Note that the AP signal 
is duplicated in two bit positions to permit this signal to always appear on memory pin A10. Table 24-14 
lists the SDRAM interface connections for different configurations of JEDEC SDRAM.

Table 24-12.   JEDEC Standard Single Data Rate SDRAMs

SDRAM Configuration

Item

64 Mbit

128 Mbit

256 Mbit

Bus  Width

16

32

16

32

16

32

Depth

4 Mword

2 Mword

8 Mword

4 Mword

16 Mword

8 Mword

Refresh Rows

4096

(15.62 

µ

s)

4096

(15.62 

µ

s)

4096

(15.62 

µ

s)

4096

(15.62 

µ

s)

8192

(7.81 

µ

s)

8192

(7.81 

µ

s)

# Banks

4

4

4

4

4

4

Bank Address

2

2

2

2

2

2

Row Address

12

11

12

12

13

13

Column Address

8

8

9

8

9

8

Data

Qualifiers

2

4

2

4

2

4

Summary of Contents for DragonBall MC9328MX1









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DragonBall MC9328MX1

Renesas Asynchronous SH7145F Application Note preview
Asynchronous SH7145F
Brand: Renesas Pages: 17
ROE EVISON HD101 User Manual preview
EVISON HD101
Brand: ROE Pages: 41
Cervoz MEC-COM-2032i User Manual preview
MEC-COM-2032i
Brand: Cervoz Pages: 22
Nvidia Quadro M6000 Sync User Manual preview
Quadro M6000 Sync
Brand: Nvidia Pages: 8
Silicon Systems SiliconDrive SSD-P16G(I)-3100 Datasheet preview
SiliconDrive SSD-P16G(I)-3100
Brand: Silicon Systems Pages: 108
BIIZZY zoomno MSC-5578 Setup Instructions preview
zoomno MSC-5578
Brand: BIIZZY Pages: 2
PADAUK PDK5S-P-003 User Manual preview
PDK5S-P-003
Brand: PADAUK Pages: 27
ETAS XETK-S22.0 User Manual preview
XETK-S22.0
Brand: ETAS Pages: 84
ATI Technologies Radeon Online Manual preview
Radeon
Brand: ATI Technologies Pages: 87
Cypress Semiconductor CY8C24223A Specification Sheet preview
CY8C24223A
Brand: Cypress Semiconductor Pages: 31
Digital Equipment ChannelWorks Network Installer Manual preview
ChannelWorks
Brand: Digital Equipment Pages: 90
Miranda Imagestore Intuition+ User Manual preview
Imagestore Intuition+
Brand: Miranda Pages: 60
NUROTRON CS-10A Operation Manual preview
CS-10A
Brand: NUROTRON Pages: 16
Valcom VIP-814 Installation Manual preview
VIP-814
Brand: Valcom Pages: 3
Aprotech INTEL CORE i5 SYSTEM BOARD User Manual preview
INTEL CORE i5 SYSTEM BOARD
Brand: Aprotech Pages: 154
COP-USA DR3004F User Manual preview
DR3004F
Brand: COP-USA Pages: 114
Fujitsu BS2000 SE Series Quick Manual preview
BS2000 SE Series
Brand: Fujitsu Pages: 43
Fujitsu BS2000 SE Series Basic Operating Manual preview
BS2000 SE Series
Brand: Fujitsu Pages: 93

Brands by name

Popular brands

Load more brands