Motorola BSR 64000 Reference Manual Download Page 504 | Manualshive

Page: 504 / 836

background image

BSR 64000 Command Reference Guide

13-34

cable modem qos dsa

The cable modem qos dsa command triggers a dynamic service change (DSC)
initiated by the CMTS for a specified cable modem. The DSC is in a binary file that
conforms to the DOCSIS cable modem configuration file format. This configuration
file is saved in the TFTP "boot" directory on a TFTP server with a known IP address.
The current implementation has only the change of service based on service-flow (not
the flow classifier, nor the payload-header-suppression).

Group Access

MSO

Command Mode

Privileged EXEC

Command Line Usage

cable modem <ip-address> | <mac-address> qos dsa < TFTP server ip-address>
<config-file name>

Command Syntax

Note: The definition of the dynamic service is defined in a binary file that
conforms to the DOCSIS 1.1 cable modem’s configuration file format. This
configuration file is saved in the TFTP "boot" directory on a TFTP server with
known IP address.

Warning: This command should be used with extreme caution as the
dynamic service definition in the configuration file will be overwritten.

ip-address

Specified cable modem IP address to create or
delete a SID.

mac-address

Starts CM Dynamic Service Addition MAC
address of the specified cable modem.

«
...
502
503
504
505
506
...
»

Summary of Contents for BSR 64000





































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for BSR 64000

Brand: Panasonic Pages: 24

Brand: Panasonic Pages: 2

BB-HCM381A - Network Camera

Brand: Panasonic Pages: 28

BB-HCM381A - Network Camera

Brand: Panasonic Pages: 2

Marconi OMS 1200

Brand: Ericsson Pages: 136

Brand: Patton electronics Pages: 2

Brand: Lanner Pages: 78

Brand: Moxa Technologies Pages: 51

Brand: Zalip Pages: 77

EtherFast LNE100TX ver. 5

Brand: Linksys Pages: 42

Brand: UTStarcom Pages: 71

Brand: Aethra Pages: 2

Brand: Abocom Pages: 63

PowerBeam PBE-5AC-400-ISO

Brand: Ubiquiti Pages: 23

Brand: Zhone Pages: 28

HFisolator 9730/26-11

Brand: Stahl Pages: 2

Brand: ExtraHop Pages: 2

Cyclades CS4008

Brand: Avocent Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands