Motorola BSR 64000 Reference Manual Download Page 814 | Manualshive

Page: 814 / 836

background image

BSR 64000 Command Reference Guide

18-32

show clns neighbors

The show clns neighbors command displays both ES and IS neighbors.

The show clns neighbors command output is all follows:

Group Access

All

Command Mode

Privileged EXEC

Command Line Usage

show clns neighbors [cable <X/Y> | ethernet <X/Y> | gigaether <X/Y> | loopback
<1-16> | pos <X/Y> ] [ | ] [begin | exclude | include] [<WORD>]

System ID

System ID of the IS-IS router.

SNPA

Subnetwork Point of Attachment, which is the data-link layer
address.

Interface

Interface in which the system was learned from.

State

Adjacency state. Up and Init are the states of the ES or IS
neighbor.

Init

System is an IS and is waiting for an IS-IS hello message. IS-IS
regards the neighbor as not adjacent.

Up

Regards the ES or IS as reachable.

Holdtime

The number of seconds before this adjacency entry times out.

Type

The level of the IS-IS router.

Protocol

The protocol through which the adjacency was learned. Valid
protocol sources are IS-IS, IGRP, or through a static route.

«
...
812
813
814
815
816
...
»

Summary of Contents for BSR 64000





































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for BSR 64000

Brand: D-Link Pages: 267

Brand: D-Link Pages: 13

Brand: ZETR Pages: 2

Brand: CallDirect Pages: 33

Brand: Caimore Pages: 79

Brand: ICP DAS USA Pages: 8

Brand: KYLAND Technology Pages: 19

Brand: rtd Pages: 28

Brand: EMC Pages: 88

Brand: ZyXEL Communications Pages: 191

7798 I/SITE LAN

Brand: CSI Pages: 56

Brand: Intellinet Pages: 32

VDA-NVR2108W4KS2

Brand: Dahua Technology Pages: 363

Brand: Orcomm Pages: 10

Brand: Data-Tronix Pages: 15

NVR2 Series NVR2208

Brand: Dahua Pages: 181

Brand: OneAccess Pages: 54

Brand: Libtor Pages: 43

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands