manualshive.com logo in svg

Motorola BSR 64000, Reference Manual

Share
Download
Motorola BSR 64000 Reference Manual Download Page 423

VRRP Commands

10-13

ip vrrp timer

The ip vrrp timer command specifies the time interval that the Master should send 
VRRP advertisement messages. The no ip vrrp timer command restores the default.

All VRRP routers are associated with a particular virtual router, and must use the 
same advertisement interval to have VRRP run properly.

Group Access

ISP

Command Mode

Interface Configuration

Command Line Usage

ip vrrp <1-255> timer <1-255>
no ip vrrp <1-255> timer 

Command Syntax

Command Default

1 second

Note: The system is configured to send VRRP advertisements every 3 
seconds for the virtual router on the configured interface Ethernet 1/0, if the 
router is configured as the Master for the virtual router 1. If not, this interval is 
used as the factor to determine if the Master is down, if the router is 
configured as Backup for virtual router 1.

1-255

the identification number of a configured 
virtual router

timer 1-255

advertisement interval in seconds

Summary of Contents for BSR 64000





































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands