Motorola BSR 64000 Reference Manual Download Page 379 | Manualshive

Page: 379 / 836

background image

OSPF Commands

8-29

network area

The network area command defines the interfaces and area ID on which OSPF runs.
The no network area command deletes the interfaces and area ID on which OSPF
runs.

Use the network area command to cover IP address(es) for OSPF to operate on an
interface. Use the address and wildcard-mask as one command to define one or more
interfaces for an intended area.

A subnet address may be designated as the area ID if associated areas are used with IP
subnets. Each IP subnet is associated with a single area only.

Group Access

ISP

Command Mode

Router Configuration

Command Line Usage

network <ip-address> <wildcard-mask> area <area-id>
no network <ip-address> <wildcard-mask> area <area-id>

Command Syntax

Command Default

Disabled

ip-address

Network IP address.

wildcard-mask

IP address type mask with "don’t care" bits.

area-id

Network area ID, OSPF address range, either
a decimal value, or IP address if areas
associated with IP subnets then subnet area
may be specified.

«
...
377
378
379
380
381
...
»

Summary of Contents for BSR 64000





































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for BSR 64000

Brand: Barracuda Networks Pages: 2

TokenLink 3C359B

Brand: 3Com Pages: 4

TokenLink 3C359B

Brand: 3Com Pages: 8

TokenLink 3C339

Brand: 3Com Pages: 2

EtherLink 3C985B-SX

Brand: 3Com Pages: 44

Brand: 3Com Pages: 88

Brand: 3Com Pages: 2

Brand: 3Com Pages: 111

TokenLink 3C359

Brand: 3Com Pages: 4

Brand: 3Com Pages: 74

Brand: 3Com Pages: 6

Power Xpert Meter 2000

Brand: Eaton Pages: 16

POW-R-COMMAND 1000

Brand: Eaton Pages: 84

Brand: Hama Pages: 10

Brand: National Instruments Pages: 162

RIPWAVE 40-00460-00R

Brand: Navini Networks Pages: 35

Brand: E-TOP Pages: 24

Brand: Intellinet Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands