Motorola BSR 64000 Reference Manual Download Page 674

Page: 674 / 836

BSR 64000 Command Reference Guide

15-24

show controllers pos

The show controllers pos command displays high level information on the POS
controllers.

Use the show controllers pos command for troubleshooting. The following POS
controller information is provided:

SECTION:

section portion of the SONET link errors; a section can be
between the Customer Premise Equipment (CPE) and SONET
Service Provider Equipment (SPE)

B1_ERRORS = B1 BER threshold crossing alarm

LINE:

line portion errors; a line can be between a SONET SPE,
regenerators and another SONET SPE

B2_ERRORS = B2 BER threshold crossing alarm

REI_ERRORS = Remote Error Indicator

PATH:

errors that occur on the path portion of the SONET link; a path
can be between a CPE, SONET SPE, regenerators and another
SONET SPE and CPE

B3_ERRORS = B3 BER threshold crossing alarm

GI_ERRORS = G1 threshold crossing alarm

Active Defects:

list of all active SONET defects

Active Alarms:

list of current alarms as enforce by SONET alarm hierarchy

Alarm reporting
enabled for:

alarms enabled through the

pos report

command

APS:

Rx(K1/K2)/Tx(K1/K2) = contents of the received and
transmitted K1 and K2 bytes.

PATH SIGNAL
LABEL:

C2 = received value from the SONET path signal label byte

Summary of Contents for BSR 64000





































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for BSR 64000

Reviews:

Brands by name

Popular brands

Motorola BSR 64000, Reference Manual

Search results

Summary of Contents for BSR 64000

Reviews:

Brands by name

Popular brands