manualshive.com logo in svg

Motorola BSR 64000, Reference Manual

Share
Download
Motorola BSR 64000 Reference Manual Download Page 693

BGP Commands

16-11

bgp confederation peers

The bgp confederation peers command configures the ASs that belong to the 
confederation. The no bgp confederation peer command removes an AS from the 
confederation.

Use the bgp confederation peers command to configure the ASs that belong to a 
confederation. Autonomous systems specified in this command are visible internally 
to a confederation. Each autonomous system is fully meshed within itself. The BGP 
confederation identifier command specifies the confederation to which the 
autonomous systems belong.

Group Access

ISP

Command Mode

Router configuration

Command Line Usage

bgp confederation peers <1-65535>
no bgp confederation peers <1-65535>

Command Syntax

1-65535

autonomous system number

Summary of Contents for BSR 64000





































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands