Motorola BSR 64000 Reference Manual Download Page 178

Page: 178 / 836

BSR 64000 Command Reference Guide

2-60

show tcp statistics

The show tcp statistics command displays the Transmission Control Protocol (TCP)
statistics.

The following information describes the show tcp statistics command output fields:

rcvd

Statistics in this section refer to packets
received by the router.

total

Packets received.

no port

Number of packets received with no port.

checksum error

number of packets received with checksum
error

bad offset

number of packets received with bad offset to
data

too short

number of packets received that were too
short

packets in sequence

number of data packets received in sequence

dup packets

number of duplicate packets received

partially dup packets

number of packets received with partially
duplicated data

out-of-order packets

number of packets received out of order

packets with data after
window

number of packets received with data that
exceeds the receiver window size

packets after close

number of packets received after the
connection has been closed

window probe packets

number of window probe packets received

window update

number of window update packets received

dup ack packets

number of duplicate acknowledgment packets
received

Summary of Contents for BSR 64000





































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for BSR 64000

Reviews:

Related manuals for BSR 64000

Brands by name

Popular brands

Motorola BSR 64000, Reference Manual

Search results

Summary of Contents for BSR 64000

Reviews:

Related manuals for BSR 64000

Brands by name

Popular brands