Motorola BSR 64000 Reference Manual Download Page 187 | Manualshive

Page: 187 / 836

background image

IP Commands

2-69

sntp server

The sntp server command configures a router for SNTP to accept NTP traffic. The
no sntp server command disables the router receiving NTP traffic.

Group Access

System Administrator

Command Mode

Global Configuration

Command Line Usage

sntp server {<A.B.C.D> | <name>} [key <num:1-4294967295>]
no sntp server

Command Syntax

Command Default

SNTP traffic not accepted from a time server

Note: When the server address is set to 224.0.1.1, the assigned multicast
address for NTP, the BSR operates in unicast mode. It transmits a request to
this multicast address and waits for replies. It then "binds" to the first server
who replies. All subsequent transactions happen in a unicast mode. This way,
the server address need not be known beforehand.

If you configure the BSR to operate in authenticated mode, you must also
configure an authentication key (sntp authentication-key command) and a
trusted key (trusted-key command).

A.B.C.D

Server IP address.

name

HOST server name.

key num:1-4294967295 Key number for authentication purpose.

«
...
185
186
187
188
189
...
»

Summary of Contents for BSR 64000





































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for BSR 64000

Brand: Patton electronics Pages: 51

Brand: IBM Pages: 32

Brand: F5 Pages: 72

Brand: Idis Pages: 86

Brand: Paradyne Pages: 20

Brand: Paradyne Pages: 2

Brand: E-TOP Pages: 76

Brand: Vonets Pages: 8

DL-DVI-Vision-IP Series

Brand: G&D Pages: 228

Brand: CopperOptics Pages: 12

Brand: Steren Pages: 130

Brand: TRENDnet Pages: 3

Brand: Belkin Pages: 2

Brand: Supero Pages: 66

Brand: Jatontec Pages: 13

FrameSaver DSL 9783 CSU/DSU

Brand: Paradyne Pages: 233

Brand: Tripp Lite Pages: 2

Brand: Aethra Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands