Motorola BSR 64000 Reference Manual Download Page 506 | Manualshive

Page: 506 / 836

background image

BSR 64000 Command Reference Guide

13-36

cable modem qos dsc

The cable modem qos dsc command triggers a Dynamic Service Change (DSC)
initiated by the CMTS for a specified cable modem (CM).

cable modem <ip-address> | <mac-address> qos dsc <TFTP-address>
<config-filename>

Command Syntax

Command Mode

Privileged EXEC

Command Use

The cable modem qos dsc command triggers a dynamic service change (DSC)
initiated by the CMTS for a specified cable modem. The definition of the dynamic
service is defined in a binary file that conforms to the DOCSIS cable modem’s
configuration file format. This configuration file is saved in /tftpboot directory on a
TFTP server with known IP address. The current implementation only the change of
service based on service-flow (not the flow classifier, nor the
payload-header-suppression).

Command Notes

The definition of the dynamic service is defined in a binary file that conforms to the
DOCSIS cable modem configuration file format. This configuration file is saved in
the /tftpboot directory on a TFTP server with a known IP address. The current
implementation only is the change of service based on service-flow (not the flow
classifier, nor the payload-header-suppression).

ip-address

CM.

mac-address

CM MAC address.

TFTP-address

TFTP server IP address.

config-filename

CM configuration binary file.

«
...
504
505
506
507
508
...
»

Summary of Contents for BSR 64000





































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for BSR 64000

Brand: Juniper Pages: 825

8677 - BladeCenter Rack-mountable - Power Supply

Brand: IBM Pages: 126

SRA311-008P8 Series

Brand: Divio Pages: 4

Brand: RadioSPECTRAL Pages: 2

Brand: Hama Pages: 7

Brand: Sharedband Pages: 3

Brand: Teltonika Pages: 12

Brand: Patton electronics Pages: 40

ControlCenter-IP 2.0

Brand: G&D Pages: 60

Brand: TP-Link Pages: 2

Brand: Umniah Pages: 12

Brand: LOBENN Pages: 86

RouterBOARD 493

Brand: 4gon Pages: 2

SuperStack 3 4950

Brand: 3Com Pages: 67

3CRWE737A - 11Mbps Airconnect Wireless Lan PC Card PCMCIA

Brand: 3Com Pages: 6

Brand: 3Com Pages: 1177

Brand: 3Com Pages: 90

Switch 4500 PWR 26-Port

Brand: 3Com Pages: 898

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands