manualshive.com logo in svg

Motorola BSR 64000, Reference Manual

Share
Download
Motorola BSR 64000 Reference Manual Download Page 480

BSR 64000 Command Reference Guide

13-10

cable downstream frequency

The cable downstream frequency command is used to set the fixed center 
downstream frequency for RF output. The no cable downstream command returns 
the fixed center downstream frequency of RF output to the default.

Group Access

MSO

Command Mode

Interface Configuration

Command Line Usage

cable downstream [<port>] frequency [down-freq-Hz]
no cable downstream [<port>] frequency [down-freq-Hz]

Command Syntax

Command Default

555000000 Hz

Note: The digital carrier frequency cannot be the same as the video carrier 
frequency.

port

Downstream port number.

down-freq-hz

The downstream carrier center frequency. 
Valid values are from 91000000 to 
857000000 Hertz (Hz) for North American 
DOCSIS and from 100000000 to 858000000 
Hz.

Summary of Contents for BSR 64000





































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands