manualshive.com logo in svg

Motorola BSR 64000, Reference Manual

Share
Download
Motorola BSR 64000 Reference Manual Download Page 690

BSR 64000 Command Reference Guide

16-8

bgp cluster-id

The bgp cluster-id command configures a cluster ID if the BGP cluster has more than 
one route reflector. The no bgp cluster-id command removes the cluster.

Use the bgp cluster-id command to increase redundancy and avoid a single point of 
failure. Route reflectors in a cluster must be configured with a 4-byte cluster ID in 
order to be recognized from route reflectors in the same cluster. Use this command to 
configure the cluster ID if the route reflector has more than one route.

Group Access

ISP

Command Mode

Router Configuration

Command Line Usage

bgp cluster-id <value>
no bgp cluster-id <value>

Command Syntax

Command Default

router ID route reflector in cluster

value

router (as a route reflector) ID in IP address 
format

Summary of Contents for BSR 64000





































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands