Motorola BSR 64000 Reference Manual Download Page 360 | Manualshive

Page: 360 / 836

background image

BSR 64000 Command Reference Guide

8-10

area virtual-link

Use the area virtual link command to create a virtual link that connects an OSPF
area to the backbone area (area 0.0.0.0) without being physically connected to the
OSPF backbone area. Use the no area virtual-link command to delete the defined
OSPF virtual link.

Group Access

ISP

Command Mode

Router Configuration

Command Line Usage

area {<area-id> | <ip-address>} virtual-link <router-id> [hello-interval <seconds>]
[retransmit-interval <seconds>] [transmit-delay <seconds>] [dead-interval
<seconds>] [authentication-key <password> | message-digest-key <key-id>]

no area {<area-id> | <ip-address>} virtual-link <router-id> [hello-interval
<interval>] [retransmit-interval <interval>] [transmit-delay <transmit-delay>]
[dead-interval <dead-interval>] [authentication-key <password> |
message-digest-key <key-id>]

Command Syntax

area-id

OSPF area ID number.

ip-address

IP address associated with the OSPF area ID.

router-id

Router ID IP address that associated with the
virtual link neighbor, 32-bit address.

hello-interval <seconds>

Time in seconds between hello packets on an
interface, value must be the same for all
routers and access servers attached to a
common network.

«
...
358
359
360
361
362
...
»

Summary of Contents for BSR 64000





































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for BSR 64000

Brand: D-Link Pages: 13

Brand: Panasonic Pages: 4

Brand: Konica Minolta Pages: 38

Brand: Western Digital Pages: 8

JetNet 3508-LVDC

Brand: Korenix Pages: 16

2000 IDU Series

Brand: EMS Pages: 52

301297U - 1TB Ethernet Disk XP Embedded Network Attached...

Brand: LaCie Pages: 67

Brand: Digisol Pages: 22

Brand: NBase Pages: 18

Brand: Gearlinx Pages: 23

Brand: Tripp Lite Pages: 2

Brand: Zhone Pages: 28

HFisolator 9730/26-11

Brand: Stahl Pages: 2

Brand: Idis Pages: 18

OmniStor 4900F Series

Brand: Rackable Systems Pages: 196

WRT330N - Wireless-N Gigabit Gaming Router Wireless

Brand: Linksys Pages: 92

Brand: ZyXEL Communications Pages: 36

Brand: Tripp Lite Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands