Motorola BSR 64000 Reference Manual Download Page 810 | Manualshive

Page: 810 / 836

background image

BSR 64000 Command Reference Guide

18-28

show clns interface

The show clns interface command displays the CLNS interface status and
configuration.

The show clns interface command output is as follows:

interface

The specific interface is described in the output and is
described as being up (functional) and the line protocol as
being up (functional) or administratively down.

CLNS protocol
processing

Describes whether or not the CLNS protocol is enabled or
disabled.

Checksums
enabled

The checksums can be enabled or disabled.

MTU

The maximum transmission unit size for a packet on this
interface.

Next Esh/Ish

Shows when the next ES hello or IS hello packet is sent on this
interface.

Routing Protocol

Describes the routing protocol on this interface. Below this
field, information for Level 1 and/or Level 2 is displayed.

Circuit Type

Indicates whether the interface has been configured for local
routing (Level 1), area routing, (Level 2), or local and area
routing (Level 1 and 2).

Metric

Indicates the routing metric assigned to the Level 1 or Level 2
router.

Priority

Indicates the priority of the IS on this interface.

Circuit ID

Indicates the ISIS circuit ID.

Number of active
level-1 adjacencies

Indicates the number of active Level 1 adjacencies.

Number of active
level-2 adjacencies

Indicates the number of active Level 2 adjacencies.

«
...
808
809
810
811
812
...
»

Summary of Contents for BSR 64000





































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for BSR 64000

Brand: Idis Pages: 86

Brand: Paradyne Pages: 20

Brand: Paradyne Pages: 2

Brand: QNAP Pages: 39

MultiConnect SE MTS2EA

Brand: Multitech Pages: 2

StorageWorks AIT 35GB AutoLoader

Brand: Compaq Pages: 4

Brand: Netis Pages: 16

Brand: Neousys Technology Pages: 39

Brand: Dantel Pages: 22

Brand: Supero Pages: 54

OmniSwitch 6624

Brand: Alcatel Pages: 546

Internet Security Appliances

Brand: SonicWALL Pages: 293

Brand: Belkin Pages: 2

iConverter GX/F

Brand: Omnitron Systems Technology Pages: 2

Brand: TRENDnet Pages: 2

Brand: Quamtum Pages: 42

Brand: Zte Pages: 172

Nuclias DNH-100

Brand: D-Link Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands