manualshive.com logo in svg

Motorola BSR 64000, Reference Manual

Share
Download
Motorola BSR 64000 Reference Manual Download Page 122

BSR 64000 Command Reference Guide

2-4

arp (global)

The arp (global) command adds a permanent entry in the ARP cache. The no arp 
command removes the entry in the ARP cache.

Group Access

ISP

Command Mode

Global Configuration

Command Line Usage

arp <ip-address> <hardware-address> <type> [alias]
no arp <ip-address> <hardware-address> <type> [alias]

Command Syntax

Command Default

no entries in table

Note: Proxy ARP is not enabled by default. ARP cache entries translate 
32-bit addresses into 48-bit hardware addresses. If the host supports 
dynamic resolution, static entries are usually not needed. Use the clear 
arp-cache command to remove all dynamically learned entries.

ip-address

four-part dotted-decimal format matching the 
local data link

hardware-address

48-bit local data link address

type

encapsulation description, usually arpa or 
snap

alias

responds to ARP as if it owns the specified 
address, if proxy arp is enabled

Summary of Contents for BSR 64000





































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands