manualshive.com logo in svg

Motorola BSR 64000, Reference Manual

Share
Download
Motorola BSR 64000 Reference Manual Download Page 124

BSR 64000 Command Reference Guide

2-6

cable helper-address

The cable helper address function disassembles a DHCP broadcast packet, and 
reassembles it into a unicast packet so that the packet can traverse the router and 
communicate with the DHCP server.

The cable helper-address command allows the operator to configure the IP address 
of the DHCP server that UDP DHCP broadcast packets be forwarded to, as Unicast 
packets. The operator can configure different DHCP server IP addresses for cable 
modems, hosts and MTAs. In each of the three cases, multiple DHCP server IP 
addresses can be configured. The ip dhcp relay information option command must 
be configured in order for the BSR 64k000 to determine the source of the broadcast 
requests.

Group Access

ISP

Command Mode

Interface Configuration (for cable interface only)

Command Line Usage

cable helper-address <A.B.C.D> {cable-modem | host | mta}

Command Syntax

A.B.C.D

IP destination address. Typically, the IP 
address of the DHCP server.

cable-modem

identifies this IP address as the DHCP server 
IP address to forward CM UDP DHCP 
broadcast packets to

host

identifies this IP address as the DHCP server 
IP address to forward host UDP DHCP 
broadcast packets to

mta

identifies this IP address as the DHCP server 
IP address to forward MTA UDP DHCP 
broadcast packets to

Summary of Contents for BSR 64000





































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands