manualshive.com logo in svg

Motorola BSR 64000, Reference Manual

Share
Download
Motorola BSR 64000 Reference Manual Download Page 625

CMTS Commands

13-155

show interface cable

The show interfaces cable command displays the following cable interface 
information:

cable port up/
administratively down

cable modem active or taken down by 
administrator

up/administratively 
down

determines if software processes handling 
lineup/protocol down interface is operational 
or taken down by the administrator

hardware

hardware type and address

internet address

internet address then subnet mask

MTU

interface maximum transmission unit (MTU)

BW

bandwidth (BW) in kilobits per second

received broadcast

total number of broadcast or multicast packets 
that interface receives

cable

downstream interface location

downstream up/
administratively down

interface administrative state

packets output

number of packets transmitted from the 
interface

bytes

number of bytes transmitted from the 
interface

discarded

number of packets discarded

output errors

errors that prevented downstream 
transmission of packets from the interface

cable

upstream cable location

upstream up/
administratively down

upstream interface administrative status

received broadcasts

upstream interface broadcast packets received

Summary of Contents for BSR 64000





































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands