Motorola BSR 64000 Reference Manual Download Page 191 | Manualshive

Page: 191 / 836

background image

IP Commands

2-73

tunnel destination

The tunnel destination command provides a tunnel interface destination. The no
tunnel destination command removes a tunnel interface destination.

Group Access

ISP

Command Mode

Interface Configuration (tunnel interface only)

Command Line Usage

tunnel destination {<address> | <hostname>}
no tunnel destination

Command Syntax

Note: The tunnel destination command specifies the endpoint of the tunnel.
If a hostname is specified, DNS must have already been configured. The host
name-to-address translation is done following the command only once. If
mapping changes occur, the command needs to be reissued and is stored as
an IP address in the configuration files.

address

IP address of the tunnel interface destination

hostname

DNS name of tunnel interface destination

«
...
189
190
191
192
193
...
»

Summary of Contents for BSR 64000





































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for BSR 64000

Brand: D-Link Pages: 14

Brand: D-Link Pages: 7

Brand: D-Link Pages: 41

Brand: D-Link Pages: 13

Brand: D-Link Pages: 15

DSN-4100 Series

Brand: D-Link Pages: 2

Brand: D-Link Pages: 2

Patton SmartNode 2300 Series

Brand: Patton electronics Pages: 2

Brand: Paradyne Pages: 12

Brand: H3C Pages: 26

AT-9424Ts/XP AC

Brand: Allied Telesis Pages: 3

LoadMaster 1500

Brand: KEMP Technologies Pages: 71

Brand: B&B Electronics Pages: 2

Brand: WAGO Pages: 2

Brand: INNOSILICON Pages: 11

Brand: ADTRAN Pages: 20

Brand: Airlinkplus Pages: 20

Brand: Planet Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands