manualshive.com logo in svg

Motorola BSR 64000, Reference Manual

Share
Download
Motorola BSR 64000 Reference Manual Download Page 743

BGP Commands

16-61

set ip next-hop

The set ip next-hop command establishes a next-hop value for the AS path. The no ip 
next-hop command to deletes the entry.

Use the ip policy route-map interface configuration command, the route-map global 
configuration command, and the match and set route-map configuration commands, 
to define the conditions for policy routing packets. The ip policy route-map 
command identifies a route map by name. Each route-map command has a list of 
match and set commands associated with it. The match commands specify the match 
criteria---the conditions under which policy routing occurs. The set commands 
specify the set actions---the particular routing actions to perform if the criteria 
enforced by the match commands are met. 

If the interface associated with the first next hop specified with the set ip next-hop 
command is down, the optionally specified IP addresses are tried in turn.
The set clauses can be used in conjunction with one another. They are evaluated in the 
following order:

Group Access

ISP

Command Mode

Route-map Configuration

Command Line Usage

set ip next-hop <A.B.C.D>
no set ip next-hop 

Command Syntax

Command Default

disabled

A.B.C.D

IP address of the next hop to which packets 
are output; address of the adjacent router

Summary of Contents for BSR 64000





































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands