Motorola BSR 64000 Reference Manual Download Page 459 | Manualshive

Page: 459 / 836

background image

DVMRP Commands

12-11

network

The network command specifies which IP interface should enable DVMRP. The no
network command removes the specified IP address to enable DVMRP.

Use the network command to be able to use a single command to define one or
multiple interfaces to be associated with DVMRP using both the prefix and
wildcard-mask arguments.

For DVMRP to operate on the interface, the specific IP address on the interface must
be covered by the network command.

This software sequentially evaluates the address/wildcard-mask pair for each
interface as follows:

•

The wildcard-mask is logically ORed with the interface IP address.

•

The wildcard-mask is logically ORed with address in the network command.

The software compares the two resulting values, and, if they match, DVMRP is
enabled on the associated interface.

Group Access

ISP

Command Mode

Router Configuration

Command Line Usage

network <A.B.C.D> <A.B.C.D>
no network <A.B.C.D> <A.B.C.D>

Command Syntax

A.B.C.D

IP address prefix, network type to broadcast

A.B.C.D

IP address-type mask that includes don’t care
bits

«
...
457
458
459
460
461
...
»

Summary of Contents for BSR 64000





































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for BSR 64000

Brand: JCG Pages: 2

Brand: Raritan Pages: 4

Ethernet Communication Module DVPEN01-SL

Brand: Delta Electronics Pages: 54

PG-FlexPlus AMU-912

Brand: ADC Pages: 130

totalstorage 200

Brand: IBM Pages: 180

Brand: Garderos Pages: 23

Brand: Paradyne Pages: 10

Brand: Wieland Pages: 2

Brand: Valcom Pages: 4

Brand: ZyXEL Communications Pages: 1

Brand: ADTRAN Pages: 4

Brand: Planet Pages: 67

EdgeSafe M40G1AC

Brand: Garland Pages: 159

Brand: Billion Pages: 2

Brand: Johnson Controls Pages: 40

Brand: D-Link Pages: 118

Brand: D-Link Pages: 121

Brand: QNAP Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands