Mitsubishi Electric NZ2GF2B-60TCRT4, User Manual

Page: 225 / 388

223
CHAPTER 8 FUNCTIONS
8
8.
3 T
e
mperat
ure Cont
rol
M
ode
(2) Remote I/O signals, remote registers, and remote buffer memory areas that
can be used
The following table lists the remote I/O signals, remote registers, and remote buffer memory areas that can be
used with this function. (The table below shows the correspondences between the terminals used and the remote
I/O signals/remote registers/remote buffer memory areas.)
(3) Setting method
1.
Set "Method selection" to "Param write" of the control mode to be used.
"CC IE Field Configuration" window  Select the temperature control module from "List of
stations"  [CC IE Field Configuration]  [Online]  [Parameter Processing of Slave Station]
2.
Set "CH  Temperature conversion setting".
● When heating-cooling control (expanded mode) or mix control (expanded mode) is selected, "CH  Temperature
conversion setting" is ignored.
●
When the setting for the Temperature conversion setting is changed from "0: Not used" to "1: Use", temperature
conversion starts. The completion of the first temperature conversion does not turn on CH
 Operation monitor (RX11 to
RX14).
Item name
Remote I/O signal, remote register, remote buffer memory
Reference
MT2 (CH2) MT3 (CH3) MT4 (CH4)
CH  Operation monitor RX12 RX13 RX14 Page 287, Appendix 1.1 (6)
CH  Sensor two-point correction offset latch completion RX28 RX2A RX2C Page 293, Appendix 1.1 (14)
CH  Sensor two-point correction gain latch completion RX29 RX2B RX2D Page 293, Appendix 1.1 (15)
CH  Sensor two-point correction offset latch request RY28 RY2A RY2C Page 300, Appendix 1.2 (9)
CH  Sensor two-point correction gain latch request RY29
RY2B RY2D
Page 300, Appendix 1.2 (10)
CH

Alert definition RWr5 RWr6 RWr7 Page 303, Appendix 2 (5)
CH  Temperature process value (PV) RWr9 RWrA RWrB Page 304, Appendix 2 (6)
CH  Input range 130H 160H 190H Page 312, Appendix 3 (5)
CH  Primary delay digital filter setting 13DH
16DH 19DH
Page 328, Appendix 3 (16)
CH  Temperature conversion setting 1C1H
1C2H 1C3H
Page 338, Appendix 3 (29)
Sensor correction function selection 1E4H Page 341, Appendix 3 (35)
Cold junction temperature compensation selection 1E9H Page 344, Appendix 3 (40)
CH  Sensor correction value setting 281H 282H 283H Page 352, Appendix 3 (51)
CH  Sensor two-point correction offset value (measured
value)
288H 28CH 290H Page 352, Appendix 3 (52)
CH  Sensor two-point correction offset value (corrected
value)
289H 28DH 291H Page 353, Appendix 3 (53)
CH  Sensor two-point correction gain value (measured
value)
28AH 28EH 292H Page 353, Appendix 3 (54)
CH  Sensor two-point correction gain value (corrected
value)
28BH 28FH 293H Page 354, Appendix 3 (55)
Cold junction temperature process value 600H Page 359, Appendix 3 (63)
Control switching monitor 602H Page 360, Appendix 3 (65)
CH  Decimal point position 621H 622H 623H Page 362, Appendix 3 (68)
Error code A00H Page 363, Appendix 3 (69)