manualshive.com logo in svg

Marvell PXA300, Developer'S Manual

The Marvell PXA300 Developer's Manual is a comprehensive and user-friendly resource for understanding and utilizing the capabilities of this powerful processor. You can easily download this manual for free from our website, providing you with valuable instructions and insights to optimize your experience with the Marvell PXA300.

Share
Download
background image

69rlq62d-f714peg4 * Memec (Headquar

ter

s) - Unique 

Tec

h,

 Insight,

 Impact

MAR

VELL CONFIDENTIAL,

 UNDER ND

A# 12101050

69rlq62d-f714peg4 * Memec (Headquar

ter

s) - Unique 

Tec

h,

 Insight,

 Impact

MAR

VELL CONFIDENTIAL,

 UNDER ND

A# 12101050

69r

lq62d-f714peg4 * Memec (Headquar

ters) - Unique 

T

ech, Insight, Impact * UNDER ND

A# 12101050

MAR

VELL CONFIDENTIAL - UNA

UTHORIZED DISTRIB

UTION OR USE STRICTL

Y PR

OHIBITED

PXA300 Processor and PXA310 Processor 
Vol. I: System and Timer Configuration Developers Manual

                         

Doc. No. MV-TBD-00 Rev. A 

CONFIDENTIAL

 Copyright © 12/13/06 Marvell

Page 248 

Document Classification: Proprietary Information

December 13, 2006

Not approved by Document Control.  For review only.

•

The units not selected by the D2 state unit power-down bits enter a low-power state.

— BPMU initiates a voltage-change sequence for VCC_APPS and VCC_SRAM for D2 state.

•

D2 state wake-ups are enabled in 

“Application Subsystem Wake-Up from D2 to D1 State Enable Register 

(AD2D1ER)”

 and 

“Application Subsystem Wake-Up from D2 to D0 State Enable Register (AD2D0ER)”

 

and activated.

•

BPMU notifies the MPMU of D2 entry. The MPMU completes actions for D2 entry by disabling the core 
PLL, disabling the ring oscillator if enabled, and sending the BPMU requested PWR_I2C commands to the 
external regulator for VCC_APPS and VCC_SRAM voltage changes.

Entering D2 State from D1 State

D1 state exits to D2 state with the assertion of any of the following wake-up events:

•

Assertion of interrupt from mini-LCD signifying completion of current frame buffer.

The following occurs after the assertion of a D1-to-D2-state wake-up event:

•

Application subsystem MFPs are set for D2 state operation

•

The units with D2 state unit operational bits cleared are powered off

•

The units selected by the D2 state unit operational bits enter a low-power state.

— BPMU initiates voltage change sequence for VCC_APPS and VCC_SRAM for D2 state

•

D2 state wake-ups enabled in 

“Application Subsystem Wake-Up from D2 to D1 State Enable Register 

(AD2D1ER)”

 and 

“Application Subsystem Wake-Up from D2 to D0 State Enable Register (AD2D0ER)”

 

and activated.

•

BPMU notifies the MPMU of D2 entry. The MPMU completes actions for D2 entry by disabling the core 
PLL; disabling the ring oscillator; disabling the system PLL and sending the BPMU requested PWR_I2C 
commands to the external regulator for VCC_APPS and VCC_SRAM voltage changes.

Behavior in D2 State

In D2 state, all application subsystem clocks to the core and all peripherals except the BPMU and OS timer are 
disabled. The core and all application subsystem peripherals except the OS timer are in a low-power, 
state-retaining state. No core peripherals are powered off in D2 state and therefore, no state information is lost 
while in D2 state. Users can program selected SRAM banks to be off in D2 state and if so, data in the selected 
SRAM banks is lost. Additionally, no interrupts are recognized and no external pin transitions other than valid 
D2 wake-up signals, reset signals and the nBATT_FAULT signals are recognized.

The BPMU watches for wake-up events that are qualified with the enabled wake-up preprogrammed by the core 
prior to entering D2 state and sent to the BPMU. However, the receiving PMU takes up to a specified amount of 
time to acknowledge the GPIO wake-up edge and begin the wake-up sequence. Refer to the PXA300 and 
PXA310 Processor Electrical, Mechanical, and Thermal Specification for this time duration. If the same 
wake-up event is enabled in 

“Application Subsystem Wake-Up from D2 to D0 State Enable Register 

(AD2D0ER)”

 and 

“Application Subsystem Wake-Up from D2 to D1 State Enable Register (AD2D1ER)”

, the 

BPMU exits to D0 state.

If the application subsystem is in D2 state and nBATT_FAULT is asserted, a wake-up event is generated to the 
BPMU, followed by an interrupt to the core if the BIE bit is set to 1, (refer to section 4.8.1 PMU control 
Register). Software must handle the interrupt by entering D4 (the MPMU is entering S3) state using a 

Summary of Contents for PXA300





















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PXA300

Sonic Frontiers Sonic Frontiers SFD-2 Owner'S Manual preview
Sonic Frontiers SFD-2
Brand: Sonic Frontiers Pages: 8
Primada PS810 Instruction Manual preview
PS810
Brand: Primada Pages: 32
Prima PFP600 Instruction Leaflet preview
PFP600
Brand: Prima Pages: 7
creative housewares taurus 912100 Instructions Manual preview
taurus 912100
Brand: creative housewares Pages: 22
Ankarsrum N30 Safety Instructions preview
N30
Brand: Ankarsrum Pages: 34
Hamilton Beach Stack & Snap 70727 Manual preview
Stack & Snap 70727
Brand: Hamilton Beach Pages: 44
Koryo KCH 754M Instruction Manual preview
KCH 754M
Brand: Koryo Pages: 8
Pyle PRJTPFL102 User Manual preview
PRJTPFL102
Brand: Pyle Pages: 6
croydon CTR4 Series Instruction Manual preview
CTR4 Series
Brand: croydon Pages: 2
Moulinex Fresh Express DJ75 Series Instruction Booklet preview
Fresh Express DJ75 Series
Brand: Moulinex Pages: 12
Gastroback DESIGN FOOD PROCESSOR ADVANCED Operating Instructions Manual preview
DESIGN FOOD PROCESSOR ADVANCED
Brand: Gastroback Pages: 84
Barco R9861520NA Installation Manual preview
R9861520NA
Brand: Barco Pages: 85
la Minerva C/E TV Operating Instructions Manual preview
C/E TV
Brand: la Minerva Pages: 30
Menuett 802-551 User Instructions preview
802-551
Brand: Menuett Pages: 36
QVS AIRVGA VW-4PH Quick Manual For Windows preview
AIRVGA VW-4PH
Brand: QVS Pages: 2
Elite Screens PicoScreen Series Quick Setup Manual preview
PicoScreen Series
Brand: Elite Screens Pages: 2
Westinghouse WST2025ZE Owner'S Manual preview
WST2025ZE
Brand: Westinghouse Pages: 14
Sapphire Audio RFR-IP Manual preview
RFR-IP
Brand: Sapphire Audio Pages: 3

Brands by name

Popular brands

Load more brands