Lenovo ThinkPad 600 Page 208 User Manual Download

Page: 208 / 221

Set the timer to enter hibernation mode from suspend mode after the
specified number of minutes:

Set the power management mode to enter by the automatic power-saving
timer:

Set the CD-ROM speed

Display Commands

Set the screen expansion:

Set where to display information:

Parameter1

Parameter2

Parameter3

S2H

30 | 60 | 90 | Disable

—

Note:

Create the hibernation file using the

HFILE

command before using the

TI H

command.

TImer

Suspend | Hibernation

—

Note:

The default is Normal.

CDSPeed

High | Normal | Silent

—

HVEXPansion

ON | OFf

—

SCreen

LCD | CRT | BOTH

—

202

IBM ThinkPad 600 Online Book

Summary of Contents for ThinkPad 600






























































































































































































































Search results

Summary of Contents for ThinkPad 600

Reviews:

Related manuals for ThinkPad 600

Brands by name

Popular brands

Lenovo ThinkPad 600, User Manual

Search results

Summary of Contents for ThinkPad 600

Reviews:

Related manuals for ThinkPad 600

Brands by name

Popular brands