Lenovo ThinkPad 600 Page 179 User Manual Download | Manualshive

Page: 179 / 221

background image

Installing the Audio Device Driver for OS/2

To install the audio device driver for OS/2:

1

Start OS/2.

2

Insert the Audio Features Diskette for OS/2 into the diskette
drive.

3

Open the OS/2 command prompt and type

MINSTALL

; then

press Enter.

4

Select the source drive as A: (the drive name for the diskette
drive of your computer).

The installation program shows Crystal Audio (Pre-Selected)
IBM OPL3 FM MIDI Synthesis (Pre-Selected).

A check mark appears next to the selected items.

5

Click on Install; then follow the instructions on the screen.

6

When you have completed the installation, restart the
computer.

Installing the ThinkPad Modem Software for OS/2

The modem function of your computer is supported by a digital signal
processor (DSP) called the IBM Advanced Communications
Processor. You must install the ThinkPad Modem software for OS/2
to use the modem function.

If you have multiple operating systems, you might need to install the
ThinkPad Modem software for each operating system. For example,
to enable OS/2 and Windows applications for ThinkPad Modem
functions, install the ThinkPad Modem software for both OS/2

and

Windows.

To install the ThinkPad Modem software for OS/2:

1

Start OS/2; then open the OS/2 screen command prompt.

2

Insert the ThinkPad Modem for OS/2 Diskette into the diskette
drive; then type

A:\SETUP

and press Enter.

The installation window appears on the screen.

Chapter 8. Installing Software

173

«
...
177
178
179
180
181
...
»

Summary of Contents for ThinkPad 600






























































































































































































































Reviews:

No comments

Related manuals for ThinkPad 600

BAKER HUGHES DPS 5000 Series

Brand: GE Pages: 36

Brand: Oemtools Pages: 8

Brand: U.S. General Pages: 5

Brand: FeiYu Tech Pages: 5

Brand: FEIYUTECH Pages: 19

Brand: FeiYu Tech Pages: 25

Brand: FEIYUTECH Pages: 16

Brand: Hahnel Pages: 176

Brand: TAUBENREUTHER Pages: 11

Brand: Yakima Pages: 15

Brand: Öhlins Pages: 8

Brand: Öhlins Pages: 9

Brand: Öhlins Pages: 8

Brand: Alpine Pages: 8

CARPOWER CAP-12XHQ

Brand: Monacor Pages: 5

Brand: Carcomm Pages: 2

Brand: Whispbar Pages: 14

Brand: J.Burrows Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands