Lenovo ThinkPad 600 Page 38 User Manual Download | Manualshive

Page: 38 / 221

background image

For Windows NT, Windows 3.11, or OS/2:

1. Click on the Battery (

) button.

2. Click on the Suspend/Hibernation/Resume options (

)

button; then select the Resume on incoming call option.

For DOS: Enter

PS2 RI E

Considerations for Hibernation Mode

Consider the following before using hibernation mode:

Do not run any tasks while the hibernation file is being created.

The computer uses battery power to enter hibernation mode.

Therefore, it reserves some battery power when it is set to enter
hibernation mode when a low-battery condition occurs. This can
cause the battery operating time to be shorter than the time
publicly stated.

Do not add or remove memory during hibernation mode. If you

do, the computer resumes from hibernation mode without
recognizing the changed memory size. To ensure that the
computer recognizes the correct memory size, shut down; then
restart your operating system.

If the computer is powered with battery power, the computer

turns power off to the PC Card when entering hibernation mode.
When resuming normal operation, if the PC Card or computer
does not operate, restart the application or computer.

32

IBM ThinkPad 600 Online Book

«
...
36
37
38
39
40
...
»

Summary of Contents for ThinkPad 600






























































































































































































































Reviews:

No comments

Related manuals for ThinkPad 600

Brand: Samsung Pages: 21

and Vantage Pro

Brand: DAVIS Pages: 4

and Vantage Pro

Brand: Davis Instruments Pages: 4

Brand: Datavideo Pages: 45

Brand: RaceChip Pages: 12

Brand: Lanier Pages: 3

Brand: UMBRA RIMORCHI Pages: 18

Brand: Vaisala Pages: 2

Brand: ICON Pages: 2

Power commander GSXR750

Brand: Dynojet Pages: 4

Brand: EVGA Pages: 15

Brand: EUROCOM Pages: 96

Sterling ALL-TERRAIN 576

Brand: Roadmaster Pages: 12

Brand: HHD Pages: 5

480L - UPDATE V3.0

Brand: Lexicon Pages: 40

Brand: SeaSucker Pages: 9

Heathkit SA-5010

Brand: Heath Pages: 3

PACMAN AIR HOCKEY 4P

Brand: NAMCO Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands