Lenovo ThinkPad 600 User Manual Download Page 19

Page: 19 / 221

Setting the RingCentral Application for New Zealand

The RingCentral** program allows you to set the number of rings for

incoming messages before it answers the call.

You can set the value by selecting:

Options - Answering - Ring Options

from the RingCentral menu.

The values x and y in the following fields must be between 2 and 5:

Answer after x rings if there are new messages.

Answer after y rings if there are no new messages.

Caller ID Support

The “Answering devices with caller ID support” can be used only

where the caller ID services is available, currently only in the U.S.

and Canada.

Chapter 2. Using Audio and Modem Features

Summary of Contents for ThinkPad 600






























































































































































































































Search results

Summary of Contents for ThinkPad 600

Reviews:

Brands by name

Popular brands

Lenovo ThinkPad 600, User Manual

Search results

Summary of Contents for ThinkPad 600

Reviews:

Brands by name

Popular brands