manualshive.com logo in svg

Lenovo ThinkPad 600, User Manual

Share
Download
Lenovo ThinkPad 600 User Manual Download Page 154

  Note 

The Wave Table MIDISynth function is supported only with
Windows 95.

For IRQ-sharing information, refer to Sharing an IRQ between
ThinkPad Modem Devices.

Installing the IBM TrackPoint Driver for Windows 95

The TrackPoint Driver Diskette for Windows 95/Windows NT contains
the software support for the PS/2 TrackPoint on Windows 95 and
Windows NT Versions 4.0. It is intended for use with the IBM PS/2
TrackPoint Version 4.0 or later. For earlier versions, no special
software is needed.

  Note 

Read the README file in the diskette and make sure you install
the latest version.

To install the TrackPoint driver for Windows 95:

1

Start Windows 95.

2

Insert the TrackPoint Driver Diskette for Windows 95/Windows
NT into the diskette drive.

3

Click on Start.

4

Click on Settings and Control Panel.

5

Double-click on the Mouse icon.

6

Select the General tab at the top of the “Mouse Properties”
window.

7

Click on Change.

8

Click on Have Disk.

9

Click on OK.

148

IBM ThinkPad 600 Online Book 

 

Summary of Contents for ThinkPad 600






























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands