Lenovo ThinkPad 600 User Manual Download

Page: 34 / 221

Customizing Power Management

This section describes how to customize power management. Use
the power management mode appropriate to your operation.

Setting the Suspend Timer

To set the suspend timer, do the following:

For Windows 95:

Start the ThinkPad Configuration program.

Click on the Power Management (

) button.

The “Power Properties” window appears.

Select the Power Mode tab.

The “Power Mode” window appears.

Select Customized.

The bottom gray portion is displayed in black, and you can
specify the timeout value in minutes in the Suspend Timer
box.

Click on OK.

For Windows NT, Windows 3.11, or OS/2:

Start the ThinkPad Configuration program.

Click on the Power Management (

) button.

Three buttons appear on the right.

Click on the Power Mode Settings (

) button.

The “Power Mode Settings” window appears.

Specify the timeout value in minutes in the Suspend Timer
box.

Click on OK.

IBM ThinkPad 600 Online Book

Summary of Contents for ThinkPad 600






























































































































































































































Search results

Summary of Contents for ThinkPad 600

Reviews:

Related manuals for ThinkPad 600

Brands by name

Popular brands

Lenovo ThinkPad 600, User Manual

Search results

Summary of Contents for ThinkPad 600

Reviews:

Related manuals for ThinkPad 600

Brands by name

Popular brands