manualshive.com logo in svg

Lenovo ThinkPad 600, User Manual

Share
Download
Lenovo ThinkPad 600 User Manual Download Page 54

 

Resources

 

Drivers

 Attributes

  Note 

The following information appears depending on the type of PC
Card:

Slot:

The slot number and assigned name for the slot.
(You can change the slot name by selecting slot
management from the options menu.)

Card:

The type of this PC Card.

Manufacturer:

The manufacturer of the PC Card.

Size:

The storage capacity of the PC Card.

Drive:

The drive letter.

Battery status:

The charge status of the SRAM Card battery.

Write protect:

The write protect status—either enabled or disabled.

File system:

The file system used by the PC storage or hard disk
card.

Port:

The communication port used by this PC modem
card.

 Resources

  Note 

Some resource information is not relevant to all types of PC
Cards. These nonrelevant resources are displayed as “Not
Applicable.”

IRQ:

The interrupt request being used.

I/O:

The starting and ending addresses of the
input/output range for the PC Card.

DMA:

The DMA channel used.

Memory range: The range of physical memory.

48

IBM ThinkPad 600 Online Book 

 

Summary of Contents for ThinkPad 600






























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands