Lenovo ThinkPad 600 Page 66 User Manual Download | Manualshive

Page: 66 / 221

background image

Note

The situation described in this example could create a problem if
you are connected to a network, especially if you are mapped to
numerous network drives. The system might run out of drive
letters to assign before all your network drives have been
properly mapped. The drive letters that MTDDRV reserves might
cause all other drive letters to be reassigned (excluding drive
letters for local hard disks or ATA cards).

For example, if you have a network drive that is normally drive F
and you install MTDDRV, the network drive will no longer be
assigned drive letter F on your system. As a result, you might
have to modify the drive letters in any network batch files that
you use. For example, if you have a network batch file that loads
your network login files from drive F and MTDDRV has reserved
drive letters F and G for memory card partitions, you must
change the drive letter in your network batch file to H (the next
available letter).

60

IBM ThinkPad 600 Online Book

«
...
64
65
66
67
68
...
»

Summary of Contents for ThinkPad 600






























































































































































































































Reviews:

No comments

Related manuals for ThinkPad 600

Brand: Panasonic Pages: 40

Brand: Parrot Pages: 19

Brand: Parrot Pages: 88

Brand: Parrot Pages: 2

Brand: Parrot Pages: 2

Brand: Parrot Pages: 11

CK 3000 Evolution

Brand: Parrot Pages: 8

CK 3000 Evolution

Brand: Parrot Pages: 106

Brand: UltraGauge Pages: 55

WINE CAPTAIN U-2115WCOL-00

Brand: U-Line Pages: 5

Brand: 2E GAMING Pages: 26

Brand: Masterack Pages: 4

Brand: Over Armour Offroad Pages: 5

Brand: ECG Pages: 24

BOS R254K-UUI-PR10-S4

Brand: Balluff Pages: 74

Brand: Hama Pages: 2

Z-MACHINE ZM-KM870R

Brand: ZALMAN Pages: 2

Brand: N-Com Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands