Lenovo ThinkPad 600 User Manual Download Page 27

Page: 27 / 221

Using the Battery Status Indicator

The battery status indicator shows the current status of the battery
pack (only when the battery is installed).

Compare the battery status indicator with the following table to
determine the condition of your battery.

Status

Condition

Green

Enough power remains for operation.

Orange

The battery pack is being charged.

Blinking
orange

The battery pack needs charging. If the indicator
starts blinking orange, the computer beeps three
times.

Off

The battery pack is not installed.

The computer is turned off or is in suspend mode

when the AC Adapter is not connected.

Chapter 4. Using Your Computer with a Battery Pack

Summary of Contents for ThinkPad 600






























































































































































































































Search results

Summary of Contents for ThinkPad 600

Reviews:

Brands by name

Popular brands

Lenovo ThinkPad 600, User Manual

Search results

Summary of Contents for ThinkPad 600

Reviews:

Brands by name

Popular brands