Lenovo ThinkPad 600 Page 81 User Manual Download | Manualshive

Page: 81 / 221

background image

Using a PC Card in DOS (with CardSoft)

This section describes CardSoft for DOS and how to use it.

CardSoft enables you to use your PC Cards in the DOS
environment. It increases the usability of PC Cards by simplifying
their installation and configuration.

CardSoft provides some DOS commands. You can see the following
information on the PC Card with these commands:

PC Card type
The resources assigned to the current PC Card
Any resource conflict with the current PC Card
The drive letter of the storage or memory card
Whether the PC Cart is turned on or off

CardSoft information

This section describes how to use the CardSoft commands as well
as the Configuration utility to help you configure and manage PC
Cards on your system.

Note

These commands are active in the directory where CardSoft
resides.

CARDINFO

CARDINFO scans the PC Card slots on your computer and shows
information about them. It also shows any warnings or error
messages that might have occurred when CardSoft configured these
cards.

You use CARDINFO command when:

You need to know the types of cards that are currently inserted

in your PC Card slots.

You need to know the I/O ports, IRQs, and memory areas that

are being used by your PC Card. This information might be
needed if you are installing other components on your system.

Chapter 5. Using Your Computer with a PC Card

75

«
...
79
80
81
82
83
...
»

Summary of Contents for ThinkPad 600






























































































































































































































Reviews:

No comments

Related manuals for ThinkPad 600

Brand: AbleNet Pages: 9

Brand: Camoplast Pages: 60

WorkCentre 7132

Brand: Xerox Pages: 3

TravelMate 4210

Brand: Acer Pages: 84

Brand: PCB Piezotronics Pages: 15

Brand: Brodit Pages: 2

Brand: Fisher-Price Pages: 12

Brand: Baader Planetarium Pages: 6

Evolion 2.1 kWh

Brand: Saft Pages: 4

Brand: AutoWatch Pages: 4

Brand: SCORPION Pages: 12

RELATIVE HUMIDITY SENSOR BT72i

Brand: CMA Dishmachines Pages: 4

MILSCO KIT# C746700

Brand: K&M Pages: 2

Brand: Car-Interface Pages: 25

2 Bike Carrier 977

Brand: Thule Pages: 6

Brand: ICP DAS USA Pages: 4

PACCAR PACMOBILE 20

Brand: DAF Pages: 18

ASA-063 ATEX Series

Brand: Brüel & Kjær Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands