manualshive.com logo in svg

Lenovo ThinkPad 600, User Manual

Share
Download
Lenovo ThinkPad 600 User Manual Download Page 144

Installing Software for Windows 95

This section describes the installation procedures for Windows 95
and its software for your ThinkPad computer.

The following versions of Windows 95 are available for your
computer:

Retail Release Version (OSR0)
Service Pack Version 1 (OSR1)
OEM Service Release Version 2 (OSR2)
OEM Service Release Version 2.1 (OSR2.1)

The OSR0 is an off-the-shelf version of Windows 95 and is available
at any retail store. The OSR1 can be downloaded from the Microsoft
Internet home page (

http://www.microsoft.com

). The OSR2.1 is

available only as preloaded versions. Since your computer
incorporates several new devices that were not available when these
versions of Windows 95 were announced, take special precautions
when installing or reinstalling these versions.

138

IBM ThinkPad 600 Online Book 

 

Summary of Contents for ThinkPad 600






























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands