Lenovo ThinkPad 600 Page 50 User Manual Download | Manualshive

Page: 50 / 221

background image

Note

If the PC Card device driver is the PC Card point enabler,
you cannot use the PC Card with ThinkPad PC Card support
software. Check with the card vendor whether the device
driver is a client device driver or a point enabler.

Power Management

Depending on the function of the PC Card, changing from one power
management mode to another might cause your ThinkPad computer
to hang. PC Card support software prevents this occurrence through
special handling during power state transition:

Card Type

Suspend Request (Fn

+

F4)

Hibernation Request (Fn

+

F12)

AC Power

Battery Power

AC Power

Battery Power

Modem or
Network

Supported

Supported

N/A

Supported

Other

Supported

Supported

Supported

Supported

Note: Standby mode is always accepted.

For more information about the PC Card support software, go to the
appropriate section according to the following table:

CardWorks for Windows 95 OSR2

Using a PC Card in

Windows 95 (with CardWorks)

CardWizard for Windows NT

Using a PC Card in

Windows NT (with CardWizard)

CardWizard for Windows 3.11

Using a PC Card in

Windows 3.11 (with CardWizard)

PC Card Director for OS/2

Using a PC Card in OS/2

(with PC Card Director)

CardSoft for DOS

Using a PC Card in DOS (with

CardSoft)

44

IBM ThinkPad 600 Online Book

«
...
48
49
50
51
52
...
»

Summary of Contents for ThinkPad 600






























































































































































































































Reviews:

No comments

Related manuals for ThinkPad 600

Brand: Vega Pages: 68

Brand: Waycon Pages: 8

Versaflo M Series

Brand: 3M Pages: 27

Speedglas 9100 Series

Brand: 3M Pages: 64

Speedglas 9100 Series

Brand: 3M Pages: 2

Brand: 3M Pages: 2

Speedglas 9002NC

Brand: 3M Pages: 52

Brand: 3M Pages: 5

Speedglas 9100 FX Series

Brand: 3M Pages: 2

Brand: kaarta Pages: 29

Brand: RaceChip Pages: 20

Brand: RayTek Pages: 2

Brand: Zebronics Pages: 6

Brand: AccuAir Pages: 40

Brand: Peak Pages: 10

Brand: AIA Pages: 8

Brand: Eco Pages: 34

Brand: Enviro Pages: 37

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands