manualshive.com logo in svg

Lenovo ThinkPad 600, User Manual

Share
Download
Lenovo ThinkPad 600 User Manual Download Page 135

Problem

Cause or Action

Performance degrades
when the computer gets
hot during use.

The processor speed might decrease under the following conditions:

Use in a hot environment
High-powered processing that requires high-power consumption

This is not a defect.

A memory shortage or
memory error occurs.

 

For DOS:

1. Use the DOS command MEM/C to review your DOS memory usage

occasionally.

2. Unload any unnecessary drivers from the CONFIG.SYS file. (For

example, unload printer drivers if you do not use a printer.)

3. Reconfigure the UMB (upper memory block) using the DEVICEHIGH

statement.

4. Use the multiple configuration setup for DOS (refer to the documents

supplied with DOS).

For Windows 3.11:

1. Try the same actions as described for DOS.
2. Unload any unnecessary programs from the WIN.INI file (for example,

FUELWIN for ac operations.)

   

Chapter 7. Solving Computer Problems

129

Summary of Contents for ThinkPad 600






























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands