manualshive.com logo in svg

Lenovo ThinkPad 600, User Manual

Share
Download
Lenovo ThinkPad 600 User Manual Download Page 153

Installing the ThinkPad Modem Software for Windows 95

The modem function of your computer is supported by a digital signal
processor (DSP) called the IBM Advanced Communications
Processor. You must install the ThinkPad Modem software for
Windows 95 to use the modem function. The Wave Table
MIDISynth function is available in the ThinkPad Modem software for
Windows 95.

To install the ThinkPad Modem software for Windows 95:

1

Start Windows 95.

2

Insert the ThinkPad Modem for Windows 95 Disk 1
(SETUP.DSK) into the diskette drive.

3

Click on Start, and then Run....

4

Type 

A:\SETUP

 and press Enter.

The ThinkPad Modem setup program removes the previous
driver if there is one, and prepares for the new registration.
After you restart your computer, you see the message
“Windows 95 found an unknown device.” Insert the ThinkPad
Modem Disk 1 for Windows 95 (SETUP.DSK), and follow the
instructions on the screen.

The ThinkPad Modem installation window appears and prompts
you to enter the destination directory for the software. If the
default directory is OK, press Enter. Otherwise, type a
directory name and press Enter.

Follow the instructions on the screen.

  Note 

You need to set the dialing properties when using the ThinkPad
Modem functions. Click on Control Panel, Modems, and then
the Dialing Properties button.

If you want to use the Wave Table MIDISynth function, open
Multimedia in Control Panel, and select the MIDI tab. Then select
Wave Table MIDISynth Device as a single instrument.

   

Chapter 8. Installing Software

147

Summary of Contents for ThinkPad 600






























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands