manualshive.com logo in svg

Lenovo ThinkPad 600, User Manual

Share
Download
Lenovo ThinkPad 600 User Manual Download Page 181

To install the TrackPoint driver for OS/2:

  1

Start OS/2.

2

Insert the TrackPoint Driver Diskette for OS/2 into the diskette
drive.

3

Go to the OS/2 command prompt and type

A:\INSTALL

Then press Enter.

Follow the instructions on the screen.

4

If you are prompted for a location to install the files, select the
drive where OS/2 is installed.

5

Restart your computer to make the new settings effective.

Installing the CD-ROM Device Driver for OS/2

  Important 

If you installed a CD-ROM device driver (Non-Listed IDE
CD-ROM in the System Configuration window) when installing
OS/2 Warp, you do not need to install the CD-ROM device driver.
Go to Installing the ThinkPad Configuration Program for OS/2.

To install the CD-ROM device driver, have ready the diskette that
came with OS/2 Warp.

1

Start OS/2; then open OS/2 System, System Setup,
Install/Remove, and Selective Install.

2

Select CD-ROM Device Support.

3

Select Non-listed IDE CD-ROM or IDE CD-ROM and click on
OK.

4

Click on Next in the “System Configuration” window.

5

Click on Next in the “OS/2 Setup and Configuration” window.

6

Select Install; then follow the instructions on the screen.

   

Chapter 8. Installing Software

175

Summary of Contents for ThinkPad 600






























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands