Lenovo ThinkPad 600 User Manual Download

Page: 9 / 221

For 3-pin power cords:

Note

The grounded adapter is required for full MPRII compliance.

IBM Power
Cord
Part Number

Used in These Countries

76H3514

Australia, New Zealand

75H3516

Canada, Thailand, U.S.

76H3518

Europe

76H3520

Denmark

76H3522

India, South Africa

76H3524

United Kingdom

76H3526

Japan

76H3528

Switzerland

76H3530

Italy

76H3532

Israel

76H3535

Korea

Selecting the Country for the Internal ThinkPad Modem

To use the internal ThinkPad modem outside the country where you
purchased the computer, you must change the country name.

In the Windows 95 desktop, click on Start, Programs,
ThinkPad Modem, and then Country Selection.

The following two windows appear:

Chapter 1. Using Your Computer Outside Your Home Country

Summary of Contents for ThinkPad 600






























































































































































































































Search results

Summary of Contents for ThinkPad 600

Reviews:

Related manuals for ThinkPad 600

Brands by name

Popular brands

Lenovo ThinkPad 600, User Manual

Search results

Summary of Contents for ThinkPad 600

Reviews:

Related manuals for ThinkPad 600

Brands by name

Popular brands