Lenovo ThinkPad 600 User Manual Download

Page: 184 / 221

Installing PC Card Support Software for DOS

Notes

If you are going to use a docking station with your computer,

you need to uninstall CardSoft for DOS first, and then
reinstall it.

If you are going to use CardWizard for Windows 3.11, do not

install CardSoft for DOS.

To install the PC Card support software for DOS:

Insert the CardSoft for DOS Diskette into the diskette drive.

At the DOS command prompt, type

A:\INSTALL

and press

Enter.

The installation window appears.

Follow the instructions on the screen.

During installation, use the Arrow keys (

↓

↑

) to highlight

your selection; then press Enter.

After the installation is complete, remove any diskette from the
diskette drive and restart the computer.

Installing the Audio Device Driver for DOS

To install the audio device driver:

Start DOS.

Insert the Audio Features Diskette for DOS into the diskette
drive.

Type

A:\INSTALL

and press Enter.

Installing the CD-ROM Device Driver for DOS

To install the CD-ROM device driver for DOS:

Start DOS.

Insert the CD-ROM Driver Diskette into the diskette drive; then
type

A:\UINSTALL

and press Enter.

178

IBM ThinkPad 600 Online Book

Summary of Contents for ThinkPad 600






























































































































































































































Search results

Summary of Contents for ThinkPad 600

Reviews:

Related manuals for ThinkPad 600

Brands by name

Popular brands

Lenovo ThinkPad 600, User Manual

Search results

Summary of Contents for ThinkPad 600

Reviews:

Related manuals for ThinkPad 600

Brands by name

Popular brands