manualshive.com logo in svg

Lenovo ThinkPad 600, User Manual

Share
Download
Lenovo ThinkPad 600 User Manual Download Page 120

An Indicator Problem

Problem

Action

The battery status
indicator does not go on
even though a battery
pack is installed in the
computer.

The over-current protection device inside the battery pack has been activated.
Wait several hours and try again. If the indicator still does not go on, replace
the battery pack or have the computer serviced.

 Battery Problems

Problem

Action

The battery pack cannot
be fully charged in 3
hours by the power-off
charging method.

The battery pack might be over-discharged. Do the following:

1. Turn off the computer.
2. Make sure that the over-discharged battery pack is in the computer.
3. Connect the AC Adapter to the computer and let it charge.

If the battery pack cannot be fully charged in 24 hours, use a new battery pack.

Your computer shuts
down before the battery
status indicator shows
empty.
–or–
Your computer operates
after the battery status
indicator shows empty.

Repeat discharging and charging the battery pack at least three times.

The computer does not
operate with a fully
charged battery pack.

The over-current protective function in the battery pack might be activated. Turn
off the computer for 1 minute to reset this function; then turn it back on again.

CD-ROM Drive Problems

114

IBM ThinkPad 600 Online Book 

 

Summary of Contents for ThinkPad 600






























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands