Lenovo ThinkPad 600 Page 166 User Manual Download | Manualshive

Page: 166 / 221

background image

You can connect your computer to the RAS server using the infrared
port if your RAS server is also configured for using an infrared
device.

Installing the IBM TrackPoint Driver for Windows NT

The TrackPoint Driver Diskette for Windows 95/Windows NT contains
the software support for the PS/2 TrackPoint on Windows 95 and
Windows NT Version 4.0. It is intended for use with the IBM PS/2
TrackPoint Version 4.0 or later.

Note

Read the README file in the diskette and make sure you install
the latest version.

To install the TrackPoint driver for Windows NT:

1

Start Windows NT.

2

Insert the TrackPoint Driver Diskette for Windows 95/Windows
NT into the diskette drive.

3

Click on Start.

4

Click on Settings and Control Panel.

5

Double-click on the Mouse icon.

6

Select the General tab at the top of the “Mouse Properties”
window.

7

Click on Change.

8

Click on Have Disk.

9

Click on OK.

10

Select “PS/2 TrackPoint” from the list to the right.

11

Click on OK.

12

Click on Close in the “Mouse Properties” window.

160

IBM ThinkPad 600 Online Book

«
...
164
165
166
167
168
...
»

Summary of Contents for ThinkPad 600






























































































































































































































Reviews:

No comments

Related manuals for ThinkPad 600

Brand: NEC Pages: 144

DeltaSphere-3000

Brand: 3rdTech Pages: 9

Watchdog Super Elite

Brand: 4B Pages: 76

mamaRoo 4M-005-00

Brand: 4 Moms Pages: 17

Brand: GÄN Pages: 24

Brand: Jeep Pages: 7

Brand: Yolin Pages: 25

Brand: EAL Pages: 4

Brand: UMBRA RIMORCHI Pages: 18

Brand: Vaisala Pages: 2

BMP 01-ZLZPP 1A 00-P S75 Series

Brand: Balluff Pages: 20

Brand: SECURENET Pages: 12

Heathkit SA-5010

Brand: Heath Pages: 3

Brand: Bioenno Power Pages: 2

Brand: Lafferty Pages: 4

Brand: A&D Pages: 68

Brand: Nav TV Pages: 3

TroyLee Designs

Brand: A3 HELMET Pages: 244

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands