Lenovo ThinkPad 600 Page 138 User Manual Download

Page: 138 / 221

Recovering Lost or Damaged Software

This section describes how to recover lost or damaged software.
The following table shows what is needed to recover your system.

Problem

Tools Provided

For More Information

Windows 95 and Windows NT users with a CD-ROM drive

You need to recover
a lost or damaged
device driver.

Use the ThinkPad Installer on the
ThinkPad Customization CD.

See the

User's Reference for

general information. The CD-ROM
also contains online help for
detailed instructions.

You need to recover
(reinstall) a lost or
damaged software
application.

Use the Easy Application Installer
on the ThinkPad Customization
CD.

See the

User's Reference for

general information. The CD-ROM
also contains online help for
detailed instructions.

You need to recover
your entire hard disk.

Use the ThinkPad Recovery CD.

See the

User's Reference for

general information.

Windows 95 or Windows NT users without a CD-ROM drive

You need to recover
a lost or damaged
device driver.

Use the Diskette Factory on your
hard disk drive.

See the

User's Reference for

general information about using
Diskette Factory.

You need to recover
(reinstall) a lost or
damaged software
application.

Use the Diskette Factory on your
hard disk drive.

Note:

Some applications are not
supported in Diskette
Factory.

See the

User's Reference for

general information about using
Diskette Factory.

You need to recover
your entire hard disk
drive.

Contact Microsoft for operating
system installation diskettes.

Go to the ThinkPad Web site to
download latest hardware driver
diskettes. Install them.
—

Or—

Get your computer serviced by
IBM. Some charge might apply.

See the Microsoft Windows booklet
shipped with your computer to find
out how to order Windows
installation diskettes.
—

Or—

See the

User's Reference for more

information.

OS/2 or Windows 3.1 users

132

IBM ThinkPad 600 Online Book

Summary of Contents for ThinkPad 600






























































































































































































































Search results

Summary of Contents for ThinkPad 600

Reviews:

Related manuals for ThinkPad 600

Brands by name

Popular brands

Lenovo ThinkPad 600, User Manual

Search results

Summary of Contents for ThinkPad 600

Reviews:

Related manuals for ThinkPad 600

Brands by name

Popular brands