manualshive.com logo in svg

Lenovo ThinkPad 600, User Manual

The Lenovo ThinkPad 600 is a reliable and powerful laptop designed for seamless productivity. Unlock its full potential with the comprehensive User Manual, available for free download at manualshive.com. This manual offers step-by-step instructions and valuable insights to maximize your experience with this exceptional device.

Share
Download
background image

Pressing the Down arrow key to highlight the item and then

press Enter.

Pressing a key that corresponds to the highlighted letter.

Using Storage PC Cards

This section describes how to use the storage cards.

Using the ATA Hard Disk or ATA Flash Disk Cards

For you to use ATA hard disk or ATA Flash disk cards on your
system, your CONFIG.SYS file must contain the following line. The
standard device drivers are always required:

 

DEVICEHIGH=C:\CARDSOFT\ATADRV.EXE

 

DEVICEHIGH=C:\CARDSOFT\MTDDRV.EXE

Formatting or Intializing a Card

  Attention 

Make sure you are using the correct drive letter when formatting
or initializing your ATA card, because any information on the
specified drive is erased.

Formatting an ATA Card

To format an ATA card:

1

Type the following command

FORMAT drive_letter /U

  Note 

drive_letter

 is the drive letter assigned to the card. For

example, if the card has been assigned to drive D, type

format D: /U

  2

Press Enter.

Initializing an ATA Card

   

Chapter 5. Using Your Computer with a PC Card

79

Summary of Contents for ThinkPad 600






























































































































































































































Reviews:

No comments

Related manuals for ThinkPad 600

Acer Aspire 1670 Series User Manual preview
Aspire 1670 Series
Brand: Acer Pages: 118
Acer Aspire 1350 Manuel D'Utilisation preview
Aspire 1350
Brand: Acer Pages: 94
Acer AcerNote Nuovo 970 Specifications preview
AcerNote Nuovo 970
Brand: Acer Pages: 4
Acer AcerNote 950 User Manual preview
AcerNote 950
Brand: Acer Pages: 16
Acer 9410-2829 - Aspire Manual Do Utilizador preview
9410-2829 - Aspire
Brand: Acer Pages: 108
Acer Aspire 2000 User Manual preview
Aspire 2000
Brand: Acer Pages: 130
Acer Aspire 1350 User Manual preview
Aspire 1350
Brand: Acer Pages: 93
Acer Aspire 1360 Series User Manual preview
Aspire 1360 Series
Brand: Acer Pages: 104
Hama WS-200 Operating Instruction preview
WS-200
Brand: Hama Pages: 10
Hama Neptun Manual preview
Neptun
Brand: Hama Pages: 6
Lange Originals HOIST-A-TOP JL CRANK Installation Instructions Manual preview
HOIST-A-TOP JL CRANK
Brand: Lange Originals Pages: 13
R-Go Riser Duo Instruction Manual preview
Riser Duo
Brand: R-Go Pages: 2
R&S NRP Series Getting Started preview
NRP Series
Brand: R&S Pages: 52
Uniden BTSC1500 Owner'S Manual preview
BTSC1500
Brand: Uniden Pages: 16
Uniden BTSC1500 User Manual preview
BTSC1500
Brand: Uniden Pages: 20
Panasonic Toughbook CF-74JCL02AM Operating Instructions Manual preview
Toughbook CF-74JCL02AM
Brand: Panasonic Pages: 36
Bercomac Berco 700316-4 Owner'S Manual preview
Berco 700316-4
Brand: Bercomac Pages: 20
pleasant hearth FA010S Quick Start Manual preview
FA010S
Brand: pleasant hearth Pages: 6

Brands by name

Popular brands

Load more brands