manualshive.com logo in svg

Lenovo ThinkPad 600, User Manual

Share
Download
Lenovo ThinkPad 600 User Manual Download Page 72

  Note 

The current resource information is set as the default and
appears in the input field of each item. The number that
can be set is displayed in the pull-down list box.

4

You can change the following registered information for the PC
Card. The items that can be changed differ depending on the
PC Card.

 

Card ID
I/O port address

 

IRQ level
COM number of the serial port
Memory window address
Memory window size
Card offset address

5

Click on the OK button, and save the changes.

To cancel the changes, click on the Cancel button.

Updating the CONFIG.SYS File

For PC Card Director to work correctly, the PC Card device drivers
must be registered in the CONFIG.SYS file. These drivers are
automatically registered in the CONFIG.SYS file when you install PC
Card Director following the instructions in Chapter 8, Installing
Software.

The following section describes the standard rules for each driver
registered in the CONFIG.SYS file for your reference.

Registered Drivers and Standard Rules

The following is a sample of a CONFIG.SYS file:

66

IBM ThinkPad 600 Online Book 

 

Summary of Contents for ThinkPad 600






























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands