Lenovo ThinkPad 600 Page 131 User Manual Download | Manualshive

Page: 131 / 221

background image

Problem

Action

You cannot set a higher
resolution than the
present one on your
external monitor.

Make sure that:

The ThinkPad display driver is installed correctly by doing the following:

1. Click on Start and move the cursor to Settings and Control Panel.
2. Double-click on Display.
3. Select the Settings tab in the “Display Properties” window.

|

4. (For Windows 95) Click on Advanced Properties.

|

(For Windows NT) Click on Display Type....
The “Adapter/Driver Information” window appears. Make sure that the
ThinkPad display driver is installed.

If you are not sure that the ThinkPad display driver is installed correctly,
reinstall it.

An appropriate display type or refresh rate is selected.

1. Start the ThinkPad Configuration program.

2. Click on LCD (

).

3. (For Windows 95) Click on Properties....

(For Windows NT) Click on Advanced....

4. Make sure the setting in the next window is correct.
5. Click on OK to close the window.

The screen is unreadable
or distorted.

Make sure that:

The ThinkPad display driver is installed correctly by doing the following:

1. Click on Start and move the cursor to Settings and Control Panel.
2. Double-click on Control Panel and then Display.
3. Select the Settings tab in the “Display Properties” window.
4. Click on Advanced Properties. The “Adapter/Driver Information”

window appears. Make sure that the ThinkPad display driver is
installed.

The display is set correctly.

1. Start the ThinkPad Configuration program.

2. Click on LCD (

).

3. (For Windows 95) Click on Properties....

(For Windows NT) Click on Advanced....

4. Make sure the setting in the next window is correct.
5. Click on OK to close the window.

If the settings are correct, run the tests described in the manual supplied with
the external monitor. If the tests show that the external monitor is OK, have the
computer serviced.

Wrong characters appear
on the screen.

Did you install the operating system or application program with the correct
procedure?

If you did, have the external monitor serviced.

Chapter 7. Solving Computer Problems

125

«
...
129
130
131
132
133
...
»

Summary of Contents for ThinkPad 600






























































































































































































































Reviews:

No comments

Related manuals for ThinkPad 600

Brand: Calira Pages: 14

Brand: IBM Pages: 187

Brand: IBM Pages: 389

Brand: Panasonic Pages: 252

Brand: Baintech Pages: 7

Brand: Baicheng Innovations Pages: 32

Brand: PACIFIC CYCLE Pages: 112

Brand: E+E Elektronik Pages: 14

Brand: E+E Elektronik Pages: 26

Brand: E+E Elektronik Pages: 28

Brand: E+E Elektronik Pages: 2

Brand: BW Pages: 8

Brand: Lanier Pages: 3

BMP 01-ZLZPP 1A 00-P S75 Series

Brand: Balluff Pages: 20

Brand: Panasonic Pages: 242

ASPIRE ONE 1410

Brand: Acer Pages: 256

Brand: LAZER Pages: 13

ASPIRE ONE 1410

Brand: Acer Pages: 105

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands