Kyocera Ai5555 Instruction Handbook Manual Download Page 160 | Manualshive

Page: 160 / 167

background image

A-7

Jumper Settings

Changing Jumper Settings

Media Selection Jumper - JP4

The Media Selection jumper is changed only in rare circumstances when
you want to make a Thinnet (10Base2) Ethernet connector, or when your
10BaseT hub does not support link integrity (10BaseT only).

If you change this jumper to MAN (manual) for a Thinnet connection, you
also need to change the Ethernet Interface Type Jumper.

1. To make the change, locate jumper JP4 on the board (see illustration
below).

2. Remove the jumper from the AUT (automatic) setting and place it on the
MAN (manual) setting, as shown.

BNC Connector

RXA

JP5

JP3

JP4

MAN AUTO 10BT THIN

NC-2 Board Illustration

JP10

NORM FACT

o-o o o o-o

o-o o

o o-o

TXA

«
...
158
159
160
161
162
...
»

Summary of Contents for Ai5555








































































































































































Reviews:

No comments

Related manuals for Ai5555

Brand: Acclaim Lighting Pages: 32

Brand: Jeep Pages: 19

Brand: Cansec Pages: 45

Brand: Cansec Pages: 43

Brand: Cansec Pages: 32

VLT AutomationDrive FC 302

Brand: Danfoss Pages: 128

VLT DriveMotor FCP 106

Brand: Danfoss Pages: 4

Ecomot300 AC2630

Brand: IFM Electronic Pages: 111

Brand: Lattice Pages: 23

Brand: Lattice Semiconductor Pages: 2

Brand: Lathem Pages: 4

Brand: tams elektronik Pages: 36

Brand: Vaillant Pages: 12

Brand: Wang Pages: 68

Brand: NAVITAS Pages: 14

Brand: CORNING Pages: 142

Brand: Combi Pages: 28

ArmorBlock 1732E-16CFGM12R

Brand: Allen-Bradley Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands