Kyocera Ai5555 Instruction Handbook Manual Download Page 113

Page: 113 / 167

UNIX Printing Through TCP/IP 5-23

UNIX Printing Through TCP/IP

Configuring the IP Address on the NC-2 Print Server

Using rarp (continued)

6. If the rarp daemon is running, stop it and restart it. Verify that the daemon
is running.

7. Check the printer to see that the print server is connected to the network.
Turn on the printer.

8. Wait until the printer powers up and finishes initializing to allow enough
time for the IP address to become known and to be saved in nonvolatile
memory. The NC-2 Print Server should then reset itself.

9. After the NC-2 Print Server has reset, send a ping command to verify that
the print server obtained its IP address. For example:

ping 192.9.200.200

If the print server has the address, a confirmation message displays:

192.9.200.200 is alive

10. Remove your changes to the /etc/ethers file.

11. Stop the rarp daemon and, if you want it to run, restart it.

Summary of Contents for Ai5555








































































































































































Search results

Summary of Contents for Ai5555

Reviews:

Related manuals for Ai5555

Brands by name

Popular brands

Kyocera Ai5555, Instruction Handbook Manual

Search results

Summary of Contents for Ai5555

Reviews:

Related manuals for Ai5555

Brands by name

Popular brands