Kyocera Ai5555 Instruction Handbook Manual Download Page 15 | Manualshive

Page: 15 / 167

background image

1-6 NC-2 Introduction

NC-2 Introduction

Basic Specifications

Ethernet Network Interface Controller/Internal Print Server
(NIC/IEEE 1284)

Firmware
Novell, TCP/IP, Apple, Banyan (HTTP/HTML)

Protocols
Novell: NetWare 2.15, 3.x, 4.x (NDS and Bindery based);
(IPX/SPX supports Windows compatible browser utility)
TCP/IP: ARP, RARP, BootP, ICMP, SNMP
Ethertalk: Transparent implementation Ver.1
Banyan Vines: VINES 4.11 (5), 5.0 (5), (6); Vines for UNIX ver.2

Administration & Management
HTTP server providing access to HTML pages over IP & IPX
Network Management Utility for Windows via the MAP
(Management Access Program) Browser

Network Management Utility for Macintosh
BootP Lite for Windows and NT

Printer Interface
IEEE 1284 via 26 pin Connector

Instruction Store Download:

Entire program can be updated from Windows program
operating through Novell network.

Compatible w/FTP transmission of properly formatted core image
operating through TCP/IP network supporting FTP.

Hardware
10BaseT and 10Base2
0.5 MB RAM (upgrade to 1 MB of RAM)
1 MB Flash Memory

Support Software
Management Access Program For Windows (MAP)
Network Management Utility for Windows

(NetWare specific)
(Banyan specific)

BootP (Lite) and NTBootP (for Windows & NT)
Unix Host Based Software

«
...
13
14
15
16
17
...
»

Summary of Contents for Ai5555








































































































































































Reviews:

No comments

Related manuals for Ai5555

Brand: FrSky Pages: 2

Brand: D+H Pages: 14

Brand: Haldex Pages: 8

Brand: OBaby Pages: 7

Brand: Uclear Pages: 40

ecomat 100 R 360

Brand: IFM Electronic Pages: 16

Ecomot300 AC2630

Brand: IFM Electronic Pages: 11

Brand: IFM Electronic Pages: 23

Brand: Jabra Pages: 8

Brand: Watts Pages: 4

Brand: WaterCop Pages: 4

Brand: Rabbit Pages: 12

Brand: hotset Pages: 2

Brand: knorr-baby Pages: 44

Brand: ICP DAS USA Pages: 6

Brand: Carel Pages: 48

Brand: ESBE Pages: 4

Controller CR100

Brand: Sonos Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands